Floor Hardeners

• Ideal to industrial floors where a hardwearing, hygienic, dust free environment is important. Useful for hospital clean rooms, electronic assembly plants.

• SL 1000 6m*m/10 Kg pack @ 1mm thick
• SL 2000 5m*m/10 Kg pack @ 1mm thick
• SL 4000 4m*m/ 32.15 Kg Pack @4 mm thick

• High strength floor hardening ad mixture, designed to be incorporated into fresh concrete floor slabs as an admixture. It provides a dense, tough surface with four times abrasion resistance than plain cured cement concrete & is capable of withstanding the abrasion and impact loading seen by floors slabs of with numerous industrial and manufacturing facilities. It can also be mixed in mortar consistency and placed along joints to provide shoulder reinforcement. Recommended for Industrial flooring, Railway Plot forms, Shipyards, Weighing Bridge floor Concreting etc.

• Cement, higher dosage rated yield better abrasion resistance

• A dry shake ,  Non-metallic floor  hardener with cleaned and graded non-metallic aggregate coloured in a high strength cementitious acrylic binder. Designed to be incorporated into fresh concrete  slabs. It provides a dense, tough surface with four times   abrasion  resistance than plain  cured cement concrete & is capable of withstanding  the  abrasion and impact loading seen by floors slabs of with numerous industrial and manufacturing facilities. It can also be mixed in mortar consistency and placed along joints to provide shoulder reinforcement.

• Over green concrete. Higher application  rated yield better abrasion resistance.
• General colour shades available.

• Rapidstrong FM is a dry shake, metallic floor hardener with cleared and graded, non- oxidizing metallic aggregate in a high strength cementitious binder. Designed to be incorporated into fresh concrete slabs. It provides a dense, tough surface with six times abrasion resistance than plain cured cement concrete & is capable of withstanding the abrasion and impact loading seen by floors slabs of with numerous industrial and manufacturing facilities. It can also be mixed in mortar consistency and placed along joints to provide shoulder reinforcement. Colours are available in addition to the standard natural colour.

Coverage:

• Rapid strong FM may be applied at rate 3.5 kgs/m2 over green concrete for normal traffic & 6-12 Kg/m2 for heavy traffic. Higher application rates yield better abrasion resistance.

• Easy to use. High Strength Improved adhesion of good between two blocks bond strength, compressive & tensile strength. Thin jointing with high adhesion to contribute to load bearing capacity of masonry work. Long working time. Curing not required after block work completion. Fast & Economical. Recommended to mix with 30% of water to the powder.

• Roofguard Rr - Chemical Based Rust Remover Is Very Effective Product For Removing Mild Scale And Rust, Besides Removing Thin Films Of Oil And Grease From Steel Surfaces. It Prevents Rust Formation As It Also Acts As A Passivator. 

• Simple Application By Brush
• Effective Rust Removal, Even From Areas Difficult To Reach.
• Contains No Chloride-no Chance Of Further Corrosion.
• Cost Effective Coverage 

• Removes The Rust And Prevents Rust Formation. Used For Removal Of Rust From Metals Like Structural Steel, Rib Bar, Nail, Refinery, Railways, Metals Fabrication And Maintenance Work Shop, Tank, Water Pipe Lines, Shuttering Etc., 

• It Is A Very Simple Application By Brush. In Case Of Heavy Rust Steel Reinforcement Apply Roofguard Rr Directly On The Effective Areas By Brush And Leave The Surface To React For 15-30 Minutes And Then The Rust Surface Will Change Their Colour. After That Remove The Loose Particles Of Rust By Wire Brush Roofguard Rr Can Be Diluted With Water At 1:5 Ratio For Normal Applications Like Mild Scale, Rust Besides Removing Thin Films Of Oil And Grease From Steel Surfaces.

• Hygienically packed
• Long shelf life
• Precise composition

• Rapid strong NH is a quartz-silica mixture of finely graded non-metallic aggregates, plasticizer and cement binder
• It is an economical concrete floor hardener recommended for both interior and exterior use
• It almost doubles the abrasion resistance of plain, cured concrete and is particularly valuable because of its non-rusting characteristics when floors will be frequently wet

• Coverage: Rapidstrong NH may be applied at rate 3.5 kgs/m² over green concrete for normal traffic & 6-12 Kg/m² for heavy traffic
• Pack: 25 Kgs. Bags.

• Balanced composition
• Long shelf-life
• Hygienically processed

• Rapidstrong FM is a dry shake, metallic floor hardener with cleared and graded, and non-oxidizing metallic aggregate in a high strength cementations binder
• Designed to be incorporated into fresh concrete slabs
• Rapidstrong FM provides a dense, tough surface with six times abrasion resistance than plain cured cement concrete & is capable of withstanding the abrasion and impact loading seen by floors slabs of with numerous industrial manufacturing facilities
• Rapidstrong FM can also be mixed in mortar consistency and placed along joints to provide shoulder reinforcement. Colours are available in addition to the standard natural colour

• Coverage; Rapidstrong FM may be applied at rate 3.5 kgs/m² over green concrete for normal traffic & 6-12 kg/m² for heavy traffic. Higher application rates yield better abrasion resistance.
• Pack: 25, 50 Kgs. Bag.